Skip to content
No products found
Use fewer filters or clear all
XRT Moto carries comprehensive Voltaic electric bike parts covering batteries (24V to 36V LiFePO4), motors (150W to 350W brushless), controllers (15A to 25A), 140mm disc brake systems, front suspension fork options, throttle assemblies, 12-inch to 16-inch tires and Schrader valve tubes, handlebar assemblies, and seat components. The Voltaic platform shares component architecture with Apollo, Revvi, and Senda, providing broad cross-compatibility across all four brands.
What Voltaic Parts Does XRT Moto Stock?
Parts available at XRT Moto for the Voltaic platform: 24V and 36V LiFePO4 batteries with integrated BMS, 150W to 350W brushless rear hub motor assemblies, 15A to 25A controllers with model-specific power curves, 140mm mechanical disc brake systems (rotors, callipers, pads, levers), front suspension fork upgrades with 30mm stanchions and adjustable preload, throttle assemblies with Hall-effect sensors, 12-inch and 16-inch Black Cat tires with Schrader valve tubes, and frame hardware.
From our experience with the Voltaic platform, the throttle assembly is the most frequently replaced component. In our workshop, throttle issues are almost always traced back to Hall effect sensor wear from extended daily use rather than any impact or connection fault.
What Voltage System Do Voltaic Bikes Use?
Standard Voltaic 12-inch models use 24V systems with 15A to 20A controllers. Higher performance configurations use 36V. Confirm voltage from the battery sticker before ordering. Chargers must match: 24V 2A for 24V models, 36V 2A for 36V. Installing a higher voltage battery than the original specification destroys the controller immediately. Battery capacity in Ah can be increased within the correct voltage for longer runtime.
The most common battery failure we diagnose on Voltaic bikes is capacity loss on bikes stored over winter without periodic charging. A battery that charges fully but delivers under 20 minutes of runtime has sustained deep discharge cell damage. A replacement battery restores full performance.
Are Voltaic Parts Compatible With Apollo, Revvi, and Senda?
Many Voltaic parts cross-reference with Apollo, Revvi, and Senda components due to shared platform architecture. Batteries, controllers, and motors on matching voltage systems typically cross-reference. Anderson PowerPole connectors are standard for battery connections across all four brands. JST-SM connectors are used on signal wiring. Always verify voltage, connector type, and physical dimensions before cross-brand substitution.
In our workshop, cross-brand compatibility between Voltaic and Apollo components has resolved the majority of battery and controller replacement cases on matching 24V systems without any modification required.
What Are the Most Common Voltaic Parts Failures?
The most frequently replaced components on the Voltaic platform: throttle assemblies (Hall sensor wear), battery packs (capacity decline after 300 to 500 charge cycles), brake pads (replace below 1mm), charge port assemblies (moisture intrusion), and wire harnesses (insulation abrasion from frame contact). Throttle replacement is the most common single repair on actively ridden Voltaic bikes.
What Tyre Specification Fits Voltaic Bikes?
12-inch Voltaic models: 12x2.35-inch Black Cat tires, Schrader valve tubes, 12 to 15 PSI. 16-inch models: 16x2.35-inch tires, 15 to 20 PSI. Black Cat tread: 6mm knob height, directional design. Wheel bearings: 6001-2RS front, 6002-2RS rear. Under-inflated tires increase rolling resistance, reduce battery range, and accelerate wear — check pressure before every session.
Parts by Category
Batteries and Chargers
24V LiFePO4 with integrated BMS, 2.35mm barrel charge port, 24V 2A charger. 36V configurations use model-specific connectors. Store at 60 to 80% charge. Never store depleted. BMS protects against overcharge, over-discharge, and thermal runaway. Mixing charger voltage permanently destroys the BMS.
Motors and Controllers
Brushless rear hub motors: 9-pin waterproof phase/hall connector. Controllers: 15A to 25A, model-specific power curves, 3 to 6 speed modes. Anderson PowerPole battery connections, JST-SM signal wiring. Match voltage and amperage when replacing. Aftermarket controllers not programmed for Voltaic power curves alter performance characteristics.
Brakes and Suspension
140mm mechanical disc brakes, single-piston callipers, semi-metallic pads (replace below 1mm). Front suspension fork upgrades available: 30mm stanchions, adjustable air preload (20 to 40 PSI for rider weight tuning). Fork seal replacement every 50 riding hours.
Frequently Asked Questions
What voltage system do Voltaic bikes use?
Standard Voltaic 12-inch models use 24V. Some configurations use 36V. Confirm from the battery sticker before ordering. Chargers must match exactly. Installing a higher voltage battery destroys the controller immediately. Ah capacity can be increased within the correct voltage for longer runtime.
Are Voltaic parts interchangeable with Apollo and Revvi?
Many Voltaic parts cross-reference with Apollo, Revvi, and Senda on matching voltage systems. Anderson PowerPole battery connectors and JST-SM signal wiring are shared across all four brands. Always verify voltage, connector type, and physical dimensions before cross-brand substitution.
What are the most commonly replaced Voltaic parts?
Throttle assemblies (Hall sensor degradation), battery packs (300 to 500 cycle capacity decline), brake pads (replace below 1mm), charge port assemblies (moisture damage), and wire harnesses (insulation abrasion). All five are consistently stocked at xrtmoto.com.
What tyre specification fits 12-inch and 16-inch Voltaic models?
12-inch: 12x2.35-inch Black Cat, Schrader valve, 12 to 15 PSI. 16-inch: 16x2.35-inch, 15 to 20 PSI. Wheel bearings: 6001-2RS front, 6002-2RS rear. Check pressure before every session — under-inflation accelerates wear and increases puncture risk.
Does XRT Moto offer wholesale pricing on Voltaic parts?
Yes. Dealers and volume buyers access wholesale pricing. 5+ batteries: 10% discount. 10+ tire/tube sets: 15% discount. Contact inquiry@xrtmoto.com for dealer program details.
Can Voltaic parts be fitted at home?
Battery replacement, tyre changes, and throttle fitting are manageable at home. Free installation guidance is available from our team at 1.708.710.2316 or via WhatsApp. Controller and motor replacement benefit from our technical phone guidance before attempting.
What warranty covers Voltaic parts from XRT Moto?
90-day warranty on electrical components against manufacturing defects. 30-day warranty on mechanical parts. No warranty on consumables (tires, tubes, brake pads). Installation errors and water damage to electrical components void coverage.
Are there suspension upgrades available for Voltaic bikes?
Yes. Front fork upgrades with 30mm stanchions and adjustable air preload are available for models with rigid forks. Preload: 20 PSI for lighter riders, up to 40 PSI for heavier. Fork seal replacement kits available as maintenance items.
Why Buy From XRT Moto
Cross-Platform Expertise: We stock and support Apollo, Revvi, Senda, and Voltaic — cross-compatibility knowledge prevents wrong-part orders.
Same-Day Shipping: Orders before 2 PM EST ship same day with tracking.
OEM Spec Quality: Parts meeting original voltage ratings, connector types, and safety certifications.
Free Technical Support: Compatibility verification and installation guidance by phone and WhatsApp.
Competitive Pricing: Factory-aligned pricing with no dealer markup on all Voltaic parts.