Skip to content
No products found
Use fewer filters or clear all
XRT Moto stocks comprehensive Revvi electric bike parts covering 24V to 36V LiFePO4 batteries, 150W to 350W motor assemblies, 15A to 25A controllers, front suspension fork upgrades with 30mm stanchions and adjustable air preload, complete 140mm disc brake systems, throttle assemblies, seat and handlebar components, and 12-inch to 16-inch tires and Schrader valve tubes. Revvi parts share component architecture with Apollo, Senda, and Voltaic using Anderson PowerPole and JST-SM connector standards.
What Revvi Parts Does XRT Moto Stock?
Revvi parts at XRT Moto: 24V and 36V LiFePO4 batteries with BMS, 150W to 350W brushless motor assemblies, 15A to 25A controllers, 140mm disc brake systems including individual pads, rotors, callipers, and levers, front suspension fork upgrades (30mm stanchions, 60mm travel, adjustable air preload), throttle assemblies, seat and handlebar components, CNC foot pegs, and 12-inch to 16-inch Black Cat tires with Schrader valve tubes.
From our experience with the Revvi platform, the front suspension fork upgrade is the single most impactful improvement we fit in our workshop. Revvi owners who switch from the standard rigid fork to the upgraded air fork consistently describe a significant improvement in trail handling and rider confidence on mixed terrain.
What Voltage Do Revvi Bikes Run?
Standard Revvi models operate on 24V. Some configurations use 36V. Confirm from the battery sticker before ordering. Chargers must match: 24V 2A or 36V 2A. Installing incorrect voltage causes immediate controller failure. Battery Ah capacity can be increased within the correct voltage for longer runtime.
In our workshop, Revvi throttle failures are almost always the same presentation: inconsistent speed with no predictable response at low throttle input. This is Hall effect sensor failure in the throttle assembly in virtually every case. An OEM replacement throttle resolves this.
Are Revvi Parts Compatible With Apollo and Voltaic?
Many Revvi parts cross-reference with Apollo, Senda, and Voltaic components on matching voltage systems. Anderson PowerPole battery connectors and JST-SM signal wiring are shared standards. Verify voltage, connector type, and physical dimensions before cross-brand substitution.
From our experience, Revvi battery replacements using Apollo spec components on matching 24V systems resolve in the majority of cases without modification. The shared architecture is one of the most practical ownership advantages of the Revvi, Apollo, Senda, and Voltaic platform family.
What Suspension Revvi Parts Are Available?
Front fork upgrades: 30mm stanchions, 60mm travel, positive and negative air chambers with rebound damping. Preload: 20 PSI for lighter riders, up to 40 PSI for heavier. Fork seal replacement required every 50 riding hours. Air valve cores and bushing sets stocked as maintenance items. Rear shock assemblies available for Full Suspension Revvi variants.
What Are the Most Common Revvi Parts Failures?
Throttle assemblies (Hall sensor degradation — most common), battery packs (capacity decline after 300 to 500 cycles), brake pads (replace below 1mm), charge port assemblies (moisture ingress), and wire harness insulation abrasion from frame contact. Throttle replacement accounts for the majority of Revvi service cases in our workshop.
Parts by Category
Batteries and Chargers
24V LiFePO4 with BMS, 2.35mm barrel charge port, 24V 2A charger. 36V models: model-specific connectors, 36V 2A charger. Store at 60 to 80% charge. Deep discharge below 20% causes permanent capacity loss. Never store depleted.
Motors and Controllers
Brushless rear hub: 9-pin waterproof phase/hall connector. Controllers: 15A to 25A, 3 to 6 speed modes. Anderson PowerPole battery, JST-SM signal wiring. Match voltage and amperage when replacing. Model-specific power curve programming.
Tires, Tubes, and Suspension
12-inch: 12x2.35-inch at 12 to 15 PSI, Schrader valves. 16-inch: 16x2.35-inch at 15 to 20 PSI. Wheel bearings: 6001-2RS front, 6002-2RS rear. Fork upgrades: 30mm stanchions, 20 to 40 PSI preload range. Fork seals every 50 hours.
Frequently Asked Questions
Are Revvi parts interchangeable with Apollo and Voltaic?
Many cross-reference on matching voltage systems. Anderson PowerPole and JST-SM connector standards are shared. Verify voltage, connector type, and dimensions before substituting.
What voltage do Revvi bikes use?
Standard: 24V. Some: 36V. Confirm from battery sticker. Installing incorrect voltage causes immediate controller failure. Ah capacity can be increased within the correct voltage.
What suspension upgrades are available for Revvi bikes?
Front fork upgrades: 30mm stanchions, adjustable air preload 20 to 40 PSI. Fork seals every 50 riding hours. Rear shock assemblies for Full Suspension variants. Most impactful single improvement for mixed terrain riding.
How often should Revvi tires be replaced?
Inspect every 50 riding hours for wear and cracking. Most active riders replace every 6 to 12 months. Maintain 12 to 15 PSI (12-inch) or 15 to 20 PSI (16-inch) before every session. Under-inflation accelerates wear.
Can I buy individual Revvi brake components rather than full kits?
Yes. Individual pads, 140mm rotors, callipers, and levers are stocked separately alongside complete brake kits. Replace only the worn component to minimise cost.
Does XRT Moto offer bulk pricing on Revvi parts?
Yes. 5+ batteries: 10% discount. 10+ tire/tube sets: 15% discount. Dealer accounts available. Contact inquiry@xrtmoto.com.
What warranty covers Revvi parts at XRT Moto?
90-day on electrical components, 30-day on mechanical parts. Consumables (tires, pads) not covered. Installation errors and water damage void coverage.
How quickly are Revvi parts shipped?
In-stock parts ordered before 2 PM EST ship same day with tracking. Standard US delivery: 3 to 5 business days. Batteries ship ground only.
Why Buy From XRT Moto
Broadest Cross-Platform Stock: Revvi, Apollo, Senda, and Voltaic parts in one catalogue.
Fork Upgrade Expertise: We spec and fit Revvi suspension fork upgrades — the most impactful single improvement available.
Same-Day Shipping: Orders before 2 PM EST ship same day with tracking.
Individual Component Sales: Buy only the part that needs replacing — pads, rotors, levers sold individually.
Free Phone Support: Technical guidance at 1.708.710.2316 before and after purchase.